Rikon Power Tools 25-010H Owner's Manual Page 1

25-010Hwww.rikontools.com25-010HM210” Planer / Jointer with Helical CutterheadOperator’s ManualRecord the serial number and date of purchase in your m

10ASSEMBLYInstalling the Infeed Table - Continued from page 93. Insert the bar through the table’s end hole and under-side of the table. Then re-atta

11ASSEMBLYFIG. 13FIG. 12OUTFEED TABLE INSTALLATION THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE

12ADJUSTMENTSNOTE: The jointer’s depth of cut can be set by using the various lines on the scale. The top line is zero and the bottom line indicates

13ADJUSTMENTSThe jointer fence provides lateral support for the work-piece when surface planing. It can be tilted to any angle between 90° and -45°, a

ADJUSTMENTS14PLANER HEIGHT ADJUSTMENTFIG. 22FIG. 23FIG. 18Height adjustment of the planer’s table is made with the Handle (#130, FIG. 22, A). One full

ADJUSTMENTS15ADJUSTING THE PLANER TABLE1. The planer table is attached to the cabinet and move vertically by four Threaded Spindles, or posts (#131,

16ADJUSTING THE CUTTERHEADThe Cutterhead that holds the knife inserts is fastened to the machine’s cabinet, and is not adjustable. Based on the postio

17ADJUSTMENTSADJUSTING DRIVE BELTSThe cutterhead drive belt and the feedgear drive belts need to be checked periodically and retightened if necessary.

18The function of the jointer is to surface plane at, one side or edge of a board/workpiece. To use the jointer:1. The chip ejection hood should be

19 It is extremely important that a dust collection system is used with this planer to eliminate harmful airborne dust, p

2TABLE OF CONTENTSSPECIFICATIONSNOTE: The specications, photographs, drawings and information in this manual represent the current model when the man

20OPERATIONSNIPEThe term 'snipe' refers to the depression that may occur at the front or rear of a board during planing. It is caused by une

21 This machine must be grounded. Replacement of the power supply cable should only be

SYMPTOM POSSIBLE CAUSES SOLUTIONSMachine will not start. 1. No power2. Blown fuse3. ON / OFF switch not functioning4. Motor failure 1. Check power sou

SYMPTOM POSSIBLE CAUSES SOLUTIONSTROUBLESHOOTING THE JOINTER - continuedMilled surface grain is rough, raised or fuzzy1. Lumber has a high moisture co

24PARTS DIAGRAMFRAME &TABLE ASSEMBLYNOTE: Please reference the Manufacturer’s Part Numberwhen calling for Replacement Parts. For Parts under Warra

PARTS LIST25MFG. PART NO.Roller Chain – pitch 6 – 210 linksDrive Chain Protection PlateWasher – 6mmØSetting BracketGuide Rail – leftGuide ScrewG

PARTS DIAGRAM26FENCE &DRIVE ASSEMBLYNOTE: Please reference the Manufacturer’s Part Numberwhen calling for Replacement Parts. For Parts under Warra

PARTS LIST27MFG. PART NO.Locking Lever - leftJ-Belt Pulley – 5J x 42Bearing CupO-Ring – Ø40 x 2.65Grooved Ball Bearing - 6203Guide BarFence Ca

PARTS DIAGRAM28MOTOR & CABINETNOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts.For Parts under Warranty, t

PARTS LIST29Washer – 6.4mmON/OFF SwitchHex Head Bolt – M8 x 16mmSide PanelHex Head Bolt – M6 x 40mmWasher – 8mmFront PanelPoly-V-Belt – 5PJ86

3SAFETY SYMBOLSIMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be fol

NOTESUse this section to record maintenance, service and any calls to Technical Support:ACCESSORIES25-910 MOBILE BASE 25-599 INSERT KNIVES - PACK of

31WARRANTY

www.rikontools.com25-010HM225-010HFor more information:16 Progress RdBillerica, MA 01821877-884-5167 / [email protected]

4SAFETY INSTRUCTIONS 16. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to the “OFF” p

5 THIS SYMBOL DESIGNATES THAT THIS TOOL IS LISTED BY THE INTERTEK TESTING SERVICES, TO UNITED STATES AND CANADIAN STANDARDS. SAF

6SPECIFIC SAFETY INSTRUCTIONS FOR PLANER / JOINTERS 1. Do not operate this machine until you have read all of the following instructions. 2. Do not

GETTING TO KNOW YOUR MACHINECONTENTS OF PACKAGEHA On / Off Safety SwitchB Cutterhead GuardC Jointer Dust Port - Work PositionD Outfeed TableE Joi

8CONTENTS OF PACKAGEFIG. 1A. Outfeed TableB. Infeed TableC. Fence AssemblyD. Legs & Floor PadsE. Dust Hood F. Depth of Cut Control BarG.

9ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ASSEMBLY I